Force10 Networks Force10 Bedienungsanleitung PDF herunterladen (Seite 33)

Installing and Maintaining the E1200i System 33

To install fan trays:

Table 3 is an illustration of the fan tray safety labels:

Step Task

1. Unpack the fan tray.

2. Prior to inserting a fan tray, fully turn its screw latch counter-clockwise (with flathead screwdriver) until

the fan tray latching mechanism fully retracts into the fan tray (see Figure 10).

3. Grip the fan tray handle. Slide the connector end of each fan tray into the slot until it stops and the

handle end is flush with the chassis rear.

4. Secure the fan trays into place by turning the screw latch clockwise.

Table 3 Fan Tray Safety Labels

Label Location

Fan tray faceplate

FN00051A

1 2 ... 28 29 30 31 32 33 34 35 36 37 38 ... 104 105

Installing and Maintaining 1
Trademarks 2
Statement of Conditions 2
Specifications” on page 91 2
Contents 3
Appendix E 6
List of Figures 7
List of Tables 9
Chapter 1 About This Guide 11
Related Publications 12
Chapter 2 The E1200i System 13
18 The E1200i System 18
Chapter 3 Site Preparation 19
Rack Mounting 20
Cabinet Placement 20
Fans and Airflow 21
Storing Components 22
FN00058A 24
FN00046B 25
26 Installing the AC Chassis 26
30 Installing the DC Chassis 30
32 Installing Fan Trays 32
To install fan trays: 33
34 Installing Fan Trays 34
Securing the Chassis Ground 36
Installing Power Supplies 36
Operational Lit: GREEN 39
Loss of Power Unlit 39
Table 5 Fan Tray LEDs 39
Status LED is 39
Figure 15 E1200i DC PEM 41
Installing DC PEMs 42
FN00103lp 43
Retaining 43
PEM interlock lever 44
Locking screws 44
Over current protector 44
Step Task (continued) 45
Unpacking an RPM or Line Card 49
Line Cards 50
Blank Panels 51
FN00036CH 52
Load first 52
FN00029B 52
RPM Label and LEDs 53
to the left-most slot (0) 54
Table 6 RPM LEDs 54
SFM Front Panel and LEDs 55
RPM Ports 57
87654321 58
60 RPM Ports and Cables 60
Chapter 11 Powering Up 61
Supplying Power - AC 62
Supplying Power - DC 62
Booting to the CLI Prompt 63
64 Powering Up 64
Components 65
Standby switch is in Standby 67
Remove a DC Power Supply 70
Removing and Replacing SFMs 72
FN00055A 73
FN00054A 76
Appendix B System Boot 79
Step Command Task 80
show boot selector 81
show bootflash 81
86 System Boot 86
Appendix C Alarms 87
Power Supplies and Alarms 88
SFMs and Alarms 89
90 Alarms 90
• Agency Compliance 91
92 System Specifications 92
Environmental Specifications 94
Agency Compliance 94
• CUS UL 60950-1, 1st Edition 95
• CSA 60950-1-03, 1st Edition 95
• EN 60950-1, 1st Edition 95
Electromagnetic Emissions 96
Immunity 96
98 System Specifications 98
Appendix E Technical Support 99
Accessing iSupport Services 100
Step Task 102
104 Index 104
Warning 12 105
WEEE 97 105

Kommentare zu diesen Handbüchern

Keine Kommentare

Force10 Networks Force10 Bedienungsanleitung Seite 33

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Vernetzung Force10 Networks Force10